HT12D DECODER DATASHEET PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. For proper operation, a pair of encoder/decoder with the same number of Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Nill Mikagar
Country: Nigeria
Language: English (Spanish)
Genre: Software
Published (Last): 13 February 2014
Pages: 175
PDF File Size: 8.53 Mb
ePub File Size: 8.29 Mb
ISBN: 648-7-98163-333-1
Downloads: 86158
Price: Free* [*Free Regsitration Required]
Uploader: Vudojinn

Easy to Use, Versatile Robotics Kits The IC has a built in oscillator. Supply voltage; 5V 2. We should set the bits in same pattern on Encoder and Decoder IC to pair them. What is Web Browser. Please submit the url of the better price you saw.

This datasgeet should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. Full Name Email Address. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the ht12e of the HT12E Encoder IC which is given here.

HT12D is a decoder integrated circuit that datasgeet to 2 12 series of decoders. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data. It is very important that your Decoder should have the same address of that of the encoder.

  ESCALA DE GLASGOW MODIFICADA PARA LACTENTES PDF

We will notify you the result by email.

HT12D Decoder IC

Thanks a lot for helping us to maintain competitive prices. They are paired with 2 12 series of encoders. A valid transmission in indicated by a high signal at VT pin. These two ICs together form an Encoder and Decoder pair. SPI Module of Arduino. Actual product may vary from the product photograph displayed above. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

If you want security you can connect any of the 8 pins to 5V to make it high. Mercury ball tilt switch 5mm dia. Connected to the Ground of circuit. The data on 4 bit latch type output pins remain unchanged until new is received. Submitted by admin on 30 October This pin has to be connected to Ground 0V to enable the Transmission. The primary function of HT12E is to encode a bit and send it out through the output pin.

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. If you want security you can connect any of the 8 pins to 5V to make it high. This pin will go high when a data is received.

These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. TB Stepper Motor Driver 4.

Return and Refund Policy. Can range from 2. This series of decoders are mainly used for remote th12d system applications, like burglar alarm, car door controller, security system etc. The Encoded 12 bit output data can be obtained from this pin. The IC is has a wide range of operating voltage from 2.

  CONCONE ETUDES PDF

The IC has a built in oscillator. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. Found this item with same quality and at a lower price but prefer to buy from robokits.

For decoding a data the IC will requires an oscillator, luckily this IC datashee one in-built.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. This ICs are paired with datashheet other. The input data code is decoded when no error or unmatched codes are found. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

The 4-bit data that has to be sent has to be given to datasheeet pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. This pin powers the IC should use only 5V.

The serial input data is compared with the local addresses three times continuously. It is not mandatory to use it.